Constant Voltage NET LED Driver high quality
● Constant voltage output,50/60Hz
● Aluminum case with cable,Class I, IP20
● Built-in EMI filter with tiny ripple,flicker-free
● High performace and reliability
● Typical lifetime ≥ 50000 hours
● 100% full load bur-in test
● Protection: Short circuit/Over voltage/Over load
● 3 years warranty
Model | Power | Input voltage | Output voltage | Output current | Effi | PF | Warranty | Size(mm) | Weight |
NC-12045-LV6H | 45W | 170-265V | 12V | 3.7A | >80% | >0.5 | 3 years | 129*35*23mm | 150g |
NC-24045-LV6H | 24V | 1.8A | |||||||
NC-12060-LV6H | 60W | 170-265V | 12V | 5A | >80% | >0.5 | 3 years | 170*35*23mm | 150g |
NC-24060-LV6H | 24V | 2.5A | |||||||
NC-12100-LV6H | 100W | 170-265V | 12V | 8A | >83% | >0.5 | 3 years | 143*48*23mm | 190g |
NC-24100-LV6H | 24V | 4A | |||||||
NC-12150-LV6H | 150W | 170-265V | 12V | 12A | >85% | >0.5 | 3 years | 183*48*23mm | 250g |
NC-24150-LV6H | 24V | 6A | |||||||
NC-12200-LV6H | 200W | 170-265V | 12V | 16A | >86% | >0.5 | 3 years | 208*63*25mm | 300g |
NC-24200-LV6H | 24V | 8A | |||||||
NC-12250-LV6H | 250W | 170-265V | 12V | 20.8A | >86% | >0.5 | 3 years | 208*63*25mm | 320g |
NC-24250-LV6H | 24V | 10.4A | |||||||
NC-12300-LV6H | 300W | 170-265V | 12V | 25A | >87% | >0.5 | 3 years | 208*63*29mm | 350g |
NC-24300-LV6H | 24V | 12A | |||||||
NC-12400-LV6H | 400W | 170-265V | 12V | 33A | >88% | >0.5 | 3 years | 227*83*29mm | 400g |
NC-24400-LV6H | 24V | 16A |
Characteristics | Frequency | 50/60Hz | ||||||||
Voltage tolerance | ±5% | |||||||||
Max Load | 80% | |||||||||
Inrush Current((A ) | <50A | |||||||||
Ripple&noise | <200mVP-P | |||||||||
hold-up/start-up time time | 100ms, 30ms,20ms/ 230VAC | |||||||||
Leakage current((mA ) | <0.5mA / 230VAC | |||||||||
Protection | Over current | above 108%-116%,power limiting, recovers automatically after fault removed | ||||||||
Over voltage | switch off, recovers automatically after fault removed | |||||||||
Short circuit | hiccup mode,recovers automatically after fault removed | |||||||||
Environment | Operating Temperature | ‘-25℃~~+50℃ | ||||||||
Storage Temperature | ‘-30℃~~+80℃ | |||||||||
Humidity | 20~~95% | |||||||||
Security | LVD | 2014/35/EU,EN61347-1:2015,EN61347-2-13:2014 | ||||||||
EMC | 2014/30/EU,EN55015:2013+A1:2015, EN61547:2009,EN61000-3-2,EN61000-3-3:2013 | |||||||||
Voltage Insulation/Isolation Resistance | I/P-O/P:3.75KVAC,I/P-O/P:>100M Ohms/500VDC/28℃/68% RH | |||||||||
Classification of Installation and Use | Class I | |||||||||
Note | ◊ All parameters NOT specially mentioned are measured at 240VAC input, max rated load and 25℃ of ambient temperature | |||||||||
◊ Ripple & Noise are measured at 20MHz of bandwidth by using a 300mm twisted pair-wire terminated with a 0.1uF & 47 uF parallel capacitor. | ||||||||||
◊ The driver is considered as a component to be operated in combination with equipment,since performance will be affected by the complete installation. | ||||||||||
◊ Good heat dissipation will prolong the working life of the driver.Please ensure good ventilation. | ||||||||||
◊ Please check if the output voltage/current of any LED lights used comply with the working voltage/current of the product. | ||||||||||
◊ Be ware of high power pressure may caused by short circut when installing metal casing products. | ||||||||||
◊ Please ensure all wires connections and polarities are correct before appling power to avoid any damages to LED Lights. | ||||||||||
◊ The product shall be installed and serviced by a qualified person. | ||||||||||
◊ Please contact supplier if a fault occurs. |